Jet Edge manufactures the widest range of waterjet pumps in the industry.
St. Michael, Minnesota (PRWEB) April 17, 2014
Featuring Jet Edge’s 90KSI X-Stream and 60KSI Dominator Series hydraulic intensifier pumps and Eco-Jet direct drive pumps, the brochure provides an overview of Jet Edge’s ultra-high pressure pump technology for precision water jet cutting, as well as a side-by-side comparison of the two pump styles.
Jet Edge Hydraulic Intensifier Pumps
Jet Edge’s Dominator and X-Stream Series hydraulic intensifier pumps are available in a wide range of sizes from 30-200hp and are capable of producing pressures from 60,000-90,000psi and flow rates of 0.6-4 gpm for water jet cutting and surface preparation applications. The pumps feature a reliable tie-rod design that eliminates threads on the high-pressure cylinders, end caps, and hydraulic cylinders, reducing the likelihood of cracking, and increasing component life. Matched-metal components prevent galling of hydraulic components. Jet Edge intensifier pumps also feature patented Metal-on-Metal seal technology the cuts in half the number of seals needing to be replaced, reducing downtime for seal changes.
Hydraulic accumulators are standard on all Jet Edge waterjet intensifier pumps. This provides smoother hydraulic pressure, reduces spikes and prolongs hydraulic pump life. Hydraulic fluid is cooled and filtered, and a rugged hydraulic center section incorporates high-duty cycle-rated piston seal and wear rings. Jet Edge’s hydraulic systems have a 4,000-hour warranty. Jet Edge water jet pumps also feature CE-marked attenuators which smooth pressure fluctuations and deliver a constant and steady stream of ultra-high pressure water to the cutting tool, ensuring optimal cut quality.
Jet Edge Eco-Jet Direct Drive Pumps
Energy efficient and economical, Jet Edge's Eco-Jet direct drive positive displacement water jet pump produces 55,000 psi (3800 bar) ultra-high pressure water for precision waterjet cutting and surface preparation applications, and supports a .015 in (.38 mm) orifice. Eco-Jet pumps feature independent attenuators which smooth pressure fluctuations, increasing cutting speeds and extending component life.
The Eco-Jet is available in three configurations, standard, PTO and TACH. The standard Eco-JET features a 30HP (22kw) electric motor which uses up to 50% less electricity than a 50hp hydraulic intensifier pump, but produces the same output. The Eco-Jet PTO utilizes a tractor PTO shaft to drive the plunger pump rather than an electric motor. The Eco-Jet PTO is available for 540 RPM and 1000 RPM PTO shafts and Category 1 and 2 three point hitches (tractor sold separately). The Eco-Jet TACH uses a tractor or skid steer’s hydraulic circuit to drive the plunger pump rather than an electric motor. It is available for hydraulic circuit units capable of producing a minimum of 50hp. Maximum pressure is dependent on the tractor’s hydraulic fluid flow and pressure. Unlike traditional industrial waterjet pumps, the Eco-Jet PTO and Eco-Jet TACH require only a standard 120 V 60 Hz power source and fresh water source, making them practical for rural machine shops and shops with a limited power supply.
Find Out More
For more information about Jet Edge waterjet pumps, visit http://www.jetedge.com or call 1-800-JET-EDGE (538-3343) or 763-497-8700. To request a brochure, call 1-800-JET-EDGE (538-3343) or 763-497-8700 or e-mail sales(at)jetedge(dot)com. View the brochure as a PDF at http://www.jetedge.com.
About Jet Edge
Established in 1984, Jet Edge is a global designer and manufacturer of waterjet systems for precision cutting, surface preparation and coating removal. Jet Edge systems are used around the world in a broad range of industries, from the world's leading airlines to automotive, aerospace, industrial manufacturers, machine and job shops. Jet Edge waterjet systems are proudly made in the U.S.A. For more information about Jet Edge, visit http://www.jetedge.com, e-mail sales(at)jetedge(dot)com or call 1-800-JET-EDGE (538-3343). Follow us on Twitter @jetedge.