ELVA Tested 4x 10 Gbps MMW Links Working Together at 4.2 km
St.Petersburg, RU (PRWEB) April 24, 2017 -- Responding to requests from customers on 4G+ (LTE-A) / 5G infrastructure, ELVA-1 has fulfilled an experimental case for testing its 4x PPC-10G 10 Gbps MMW links for non-interference ability working together from the same footprints on both sides of the trace. The purpose of this test was to get an experimental confirmation of full 10 Gbps throughput for each link from this 4x bunch. Therefor, 40 Gbps aggregated wireless channel could be built for ultra-high wideband applications. The video recording of the test is available on Facebook at the ELVA-1 page https://www.facebook.com/elva1mmw.
During the test, each of the 4x 10 Gbps links had been connected to its own traffic analyzer, to measure real throughput of the link. No throughput degradation had been registered for any link, with real 10000 Mbps for data travelling wireless at 4.2 km (2.6 miles) and returning back over a fiber loop.
The PPC-10G link uses the advantage of millimeter wave technology that allows fully eliminate RF interference between up to four neighboring radio links with two easy technics. First, by using vertical (V) or horizontal (H) polarization of RF signal. For the PPC-10G link, the choice between H/V polarization could be done during the link installation by mechanically rotating the transceiver according to “V” or “H” labels on antenna. By default, when mounting the transceiver to the antenna, it is recommended to choose “V” (vertical) polarization on both radios of the link. In the scenario of installing two parallel PPC-10G links from the same position (as for 2x 10 Gbps channel aggregation), the technician could set vertical polarization for the first link, and horizontal polarization for the second link.
Second, it is possible to re-arrange the allocated 2000 MHz bandwidth within the general E-band (71-76/81-86GHz) spectrum. Thus, at least two different sub-bands are available for PPC-10G, which is another way to eliminate RF interference when 2x - 4x link aggregation is planned. The default center frequencies for PPC-10G-E (E-band) are 75/85 GHz, but could be any within 72-75/82-85 GHz. For this, an RF Tuning feature is available through the web interface to the link chipset.
There are also other cases when RF Tuning is required, as adjusting the transmitter (Tx) and receiver (Rx) center frequencies (aka nominal frequencies) might be necessary to comply with local licensing policy of the country. For example, countries like Sweden and Nigeria allocate only 71-74/81-84 GHz spectrum for point-to-point links. Thus, when installing the PPC-10G-E in such countries, it is required to set central frequency to 72-73/82-83 GHz to comply to local legislation.
The ELVA PPC-10G link is intended for ISP applications, for Security/Safe City, 4G+/ LTE/ 5G Wireless Backhaul, Corporate Campus Networks, IPTV. This 10 Gigabit millimeter wave (MMW) technology is the best choice for wireless connectivity for distances over 1+ mile in places where fiber is not available.
About ELVA-1
Founded in 1993, ELVA-1 designs and manufactures ultra high speed radio links according to ECC and FCC requirements. The links operating frequencies include 40.5-43.5GHz, 71-76 / 81-86 GHz, and 92-95 GHz with emphasis on E-band of 71-76 / 81-86 GHz. ELVA-1 has contracted manufacturing in St. Petersburg, Russia.
For further information: http://www.elva-1.com
Michael Vaitman, Elva-1, http://elva-1.com, +46 46 56 00 346, [email protected]
Share this article